Подшипник INA MKUVE20-KGT05 INA / FAG

Print

Linear actuators
internally guided carriage
Описание:
"
H110 -mm -
 - -
B86 -mm -
 - -
L200 -mm -
 - -
 -
1) -
 -Funnel type lubrication nipple to DIN 3405-AM6
2) -
 -Length calculation:
L2 = total stroke x 1,17 + L + 25
L tot = total stroke x 1,17 + L + 81
Total stroke (GH) = effective stroke + 2 x S (mm)

ATTENTION: The allowance S designates a safety range suitable for the particular application и should at least be equivalent to the spindle pitch Pz- total stroke in mm.

Maximum support rail length L2 = 5300 mm. Actuators with a total stroke length over 1000 mm can be fitted with movable spindle supports (suffix SPU or 2SPU).
B140 -mm -
 - -
B240 -mm -
 - -
B388 -mm -
 - -
B468 -mm -
 - -
d13 -mm -
 -Tolerance for diameter: h6
d160 -mm -
 -Tolerance for diameter: g6
H171 -mm -
 - -
H2109 -mm -
 - -
H320 -mm -
 - -
H460 -mm -
 - -
H590 -mm -
 - -
H646 -mm -
 - -
H712 -mm -
 - -
L319 -mm -
 - -
L442 -mm -
 - -
L58 -mm -
 - -
L615 -mm -
 - -
L728 -mm -
 - -
L828 -mm -
 - -
O1M6 -
 - -
 -
mLaw2,2 -kg -
 -Вес of carriage
mtot(Ltot - 56) x 0,0105 + 6,5 -kg -
 - -
do x Pz20 x 5 -
 -Threaded spindle:
do x Pz = nominal spindle diameter x spindle pitch
M0x664 -Nm -
 -Permissible static moment of carriage guidance system:
The values are single loads и apply when the underside of the actuator is fully supported.
These must be reduced for combined loads.
For design criteria of the linear guidance system, see Catalogue PF1, Monorail Guidance Systems.
M0y1000 -Nm -
 -Permissible static moment of carriage guidance system:
The values are single loads и apply when the underside of the actuator is fully supported.
These must be reduced for combined loads.
For design criteria of the linear guidance system, see Catalogue PF1, Monorail Guidance Systems.
M0z1200 -Nm -
 -Permissible static moment of carriage guidance system:
The values are single loads и apply when the underside of the actuator is fully supported.
These must be reduced for combined loads.
For design criteria of the linear guidance system, see Catalogue PF1, Monorail Guidance Systems.
Ca17,9 -kN -
 -Spindle bearing arrangement:
Values are valid only for calculating Lh.
Basic axial load rating = for design criteria for the locating bearing, see Catalogue HR1, Rolling Bearings
C0a28 -kN -
 -Spindle bearing arrangement:
Values are valid only for calculating Lh.
Basic axial load rating = for design criteria for the locating bearing, see Catalogue HR1, Rolling Bearings
ly281 -cm^4 -
 -Geometrical moments of inertia of support rail
lz219 -cm^4 -
 -Geometrical moments of inertia of support rail
C21,3 -kN -
 -Basic load ratings of track roller guidance system
Values are valid only for calculating Lh.
C054 -kN -
 -Basic load ratings of track roller guidance system
Values are valid only for calculating Lh.
 -F/FM -
 -Spindle nut:
F = single nut
FM = preloaded double nut
CI10,5 -kN -
 -Basic load ratings of spindle nut
Values are valid only for calculating Lh.
F = single nut
FM = preloaded double nut

Basic load ratings C и C0 to DIN 69051. Due to the incorporated calculation algorithm, the C и C0 values may differ in comparison with earlier results to DIN 69051.
C0 I16,6 -kN -
 -Basic load ratings of spindle nut
Values are valid only for calculating Lh.
F = single nut
FM = preloaded double nut

Basic load ratings C и C0 to DIN 69051. Due to the incorporated calculation algorithm, the C и C0 values may differ in comparison with earlier results to DIN 69051.
"

Подшипник INA / FAG MKUVE20-KGT05

INA / FAG MKUVE20-KGT05
Наличие: Уточняйте

Поставщик:

(812) 327-79-70

«...назад