| mLaw | 4,3 -kg - | |
| mtot | (Ltot - 64) x 0,02 + 13,4 -kg - | | - | Вес:
(L tot - 64) x 0,02 + 13,4 |
|
| - | - | | - | L2 = total stroke x 1,2 + L + 25
For version without spindle support
L tot = total stroke x 1,2 + L + 89
L2 = total stroke x 1,23 + L + 25
For version with spindle support
L tot = total stroke x 1,23 + L + 89
Total stroke = effective stroke + 2 x S
The allowance S designates a safety range suitable for the particular application и should at least be equivalent to the spindle pitch P. Total stroke in mm.
Maximum single-piece support rail length L2 = 5300 mm.
Actuators with a total stroke length over 1200 mm can be fitted with movable spindle supports (suffix SPU or 2SPU). |
|
| do x P | 32 x 10 - | | - | do x P = nominal spindle diameter x spindle pitch |
|
| - | 115 -Nm - | | - | Maximum permissible load on drive shaft |
|
| ly | 670 -cm^4 - | | - | Geometrical moments of inertia |
|
| lz | 384 -cm^4 - | | - | Geometrical moments of inertia |
|
| CI | 45500 -N - | | - | Basic load ratings for linear recirculating ball bearing и guideway assembly
Load direction I = compressive load
ATTENTION: Values are valid only for calculating Lh. |
|
| C0 I | 134000 -N - | | - | Basic load ratings for linear recirculating ball bearing и guideway assembly
Load direction I = compressive load
ATTENTION: Values are valid only for calculating Lh. |
|
| CII | 37200 -N - | | - | Basic load ratings for linear recirculating ball bearing и guideway assembly
Load direction II = tensile load
ATTENTION: Values are valid only for calculating Lh. |
|
| C0 II | 86000 -N - | | - | Basic load ratings for linear recirculating ball bearing и guideway assembly
Load direction II = tensile load
ATTENTION: Values are valid only for calculating Lh. |
|
| CIII | 34600 -N - | | - | Basic load ratings for linear recirculating ball bearing и guideway assembly
Load direction III = lateral load
ATTENTION: Values are valid only for calculating Lh. |
|
| C0 III | 92000 -N - | | - | Basic load ratings for linear recirculating ball bearing и guideway assembly
Load direction III = lateral load
ATTENTION: Values are valid only for calculating Lh. |
|
| C | 44000 -N - | | - | Spindle nut
(according to DIN 69 051, Part 4, issued 1978) |
|
| C0 | 53000 -N - | |
| C | 27500 -N - | | - | Spindle bearing arrangement |
|
| C0 | 55000 -N - | | - | Spindle bearing arrangement |
|
| M0x | 1070 -Nm - | | - | Permissible static moment on linear guidance system:
The values are single loads и apply when the underside of the actuator is fully supported.
These must be reduced for combined loads.
For design criteria of the linear guidance system, see Catalogue PF1. |
|
| M0y | 1700 -Nm - | | - | Permissible static moment on linear guidance system:
The values are single loads и apply when the underside of the actuator is fully supported.
These must be reduced for combined loads.
For design criteria of the linear guidance system, see Catalogue PF1. |
|
| M0z | 1510 -Nm - | | - | Permissible static moment on linear guidance system:
The values are single loads и apply when the underside of the actuator is fully supported.
These must be reduced for combined loads.
For design criteria of the linear guidance system, see Catalogue PF1. |
|
