Подшипник INA MKUE-25-KGT40 INA / FAG

Print

Linear actuators
internally guided carriage, with three toothed belts
Описание:
"
H125 -mm -
 - -
B110 -mm -
 - -
L200 -mm -
 - -
 -
B180 -mm -
 -Tolerance: +/-0,1
B280 -mm -
 - -
B3112 -mm -
 - -
B490 -mm -
 - -
d19 -mm -
 -Tolerance for diameter: h6
d175 -mm -
 -Tolerance for diameter: h7
H180 -mm -
 - -
H2124,5 -mm -
 - -
H325 -mm -
 - -
H475 -mm -
 - -
H570 -mm -
 - -
L155 -mm -
 -Tolerance: +/-0,1
L339 -mm -
 - -
L467 -mm -
 - -
L59 -mm -
 - -
L620 -mm -
 - -
OM10 -
 - -
O1M8 -
 - -
 -
mLaw4,3 -kg -
 -Вес of carriage
mtot(Ltot - 64) x 0,02 + 13,4 -kg -
 -Вес:
(L tot - 64) x 0,02 + 13,4
 - -
 -L2 = total stroke x 1,2 + L + 25
For version without spindle support
L tot = total stroke x 1,2 + L + 89
L2 = total stroke x 1,23 + L + 25
For version with spindle support
L tot = total stroke x 1,23 + L + 89
Total stroke = effective stroke + 2 x S
The allowance S designates a safety range suitable for the particular application и should at least be equivalent to the spindle pitch P. Total stroke in mm.
Maximum single-piece support rail length L2 = 5300 mm.
Actuators with a total stroke length over 1200 mm can be fitted with movable spindle supports (suffix SPU or 2SPU).
do x P32 x 40 -
 -do x P = nominal spindle diameter x spindle pitch
 -115 -Nm -
 -Maximum permissible load on drive shaft
ly670 -cm^4 -
 -Geometrical moments of inertia
lz384 -cm^4 -
 -Geometrical moments of inertia
C26300 -N -
 -Basic load rating for linear recirculating ball bearing и guideway assembly

ATTENTION: Values are valid only for calculating Lh.
C041800 -N -
 -Basic load rating for linear recirculating ball bearing и guideway assembly

ATTENTION: Values are valid only for calculating Lh.
C17000 -N -
 -Spindle nut
(according to DIN 69 051, Part 4, issued 1978)
C055000 -N -
 -Spindle nut
C27500 -N -
 -Spindle bearing arrangement
C055000 -N -
 -Spindle bearing arrangement
M0x500 -Nm -
 -Permissible static moment on linear guidance system:
The values are single loads и apply when the underside of the actuator is fully supported.
These must be reduced for combined loads.
For design criteria of the linear guidance system, see Catalogue PF1.
M0y1200 -Nm -
 -Permissible static moment on linear guidance system:
The values are single loads и apply when the underside of the actuator is fully supported.
These must be reduced for combined loads.
For design criteria of the linear guidance system, see Catalogue PF1.
M0z1100 -Nm -
 -Permissible static moment on linear guidance system:
The values are single loads и apply when the underside of the actuator is fully supported.
These must be reduced for combined loads.
For design criteria of the linear guidance system, see Catalogue PF1.
"

Подшипник INA / FAG MKUE-25-KGT40

INA / FAG MKUE-25-KGT40
Наличие: Уточняйте

Поставщик:

(812) 327-79-70

«...назад