Подшипник INA MDKUSE25-KGT5 INA / FAG

Print

Tиem linear actuators
plastic dummy guideways for linear recirculating ball bearing и guideway assembly KUVE..-W
Описание:
"
H145 -mm -
 - -
B260 -mm -
 - -
L365 -mm -
 - -
 -
1) -
 -L2 = total stroke x 1,18 + L + 25
Ltot = total stroke x 1,18 + L + 86
Total stroke = effective stroke + 2 x S (mm)

Note: The allowance S designates a safety range suitable for the particular application и should at least be equivalent to the spindle pitch
Pz- total stroke in mm.

Maximum support rail length L2 = 5300 mm. Actuators with a total stroke length over 1200 mm can be fitted with movable spindle supports (suffix SPU or 2SPU).
3) -
 -Lubrication nipple to DIN 3505-AM6 (4x)
4) -
 -Slot width 8
5) -
 -Slot width 10
6) -
 -Lubrication nipple to DIN 3505-AM6
8) -
 -3,5 deep
9) -
 -Effective length BL of bellows
BL = [total stroke x 0,18 + 25] / 2
B1250 -mm -
 - -
B2185 -mm -
 - -
B3115 -mm -
 - -
B435 -mm -
 - -
B550 -mm -
 - -
B6110 -mm -
 - -
B7210 -mm -
 - -
B890 -mm -
 - -
do x Pz32x5 -mm -
 -Screw drive

do x Pz = nominal spindle diameter x spindle pitch
H175 -mm -
 - -
H2143 -mm -
 - -
H325 -mm -
 - -
H450 -mm -
 - -
H570 -mm -
 - -
L339 -mm -
 - -
L467 -mm -
 - -
L59 -mm -
 - -
 -
mtot(Ltot - 61) x 0,041 + 19,3 -kg -
 -Вес
mLaw13 -kg -
 -Вес of carriage
 -F/FM -
 -Nut

Values are valid only for calculating Lh
F = single nut
FM = preloaded double nut (flanged и cylindrical nuts).
CI24 -kN -
 -Basic load ratings of nut

Values are valid only for calculating Lh
Динамическая грузоподъемность C to DIN 69 051-4: 1978
C0 I49 -kN -
 -Basic load ratings of nut

Values are valid only for calculating Lh
Динамическая грузоподъемность C to DIN 69 051-4: 1978
CII27,5 -kN -
 -Basic load ratings of spindle bearing arrangement

Values are valid only for calculating Lh
C0 II55 -kN -
 -Basic load ratings of spindle bearing arrangement

Values are valid only for calculating Lh
 -115 -Nm -
 -Maximum drive torque:
Maximum permissible load on drive shaft
M0x9500 -Nm -
 -Permissible torque on carriage guidance system
The values are single loads и apply when the underside of the actuator is fully supported.
These must be reduced for combined loads. For design criteria of the linear guidance system, see INA Catalogue PF1.
M0y17470 -Nm -
 -Permissible torque on carriage guidance system
The values are single loads и apply when the underside of the actuator is fully supported.
These must be reduced for combined loads. For design criteria of the linear guidance system, see INA Catalogue PF1.
M0z15880 -Nm -
 -Permissible torque on carriage guidance system
The values are single loads и apply when the underside of the actuator is fully supported.
These must be reduced for combined loads. For design criteria of the linear guidance system, see INA Catalogue PF1.
lz7069 -cm^4 -
 -Geometrical moments of inertia of support rail
ly899 -cm^4 -
 -Geometrical moments of inertia of support rail
"

Подшипник INA / FAG MDKUSE25-KGT5

INA / FAG MDKUSE25-KGT5
Наличие: Уточняйте

Поставщик:

(812) 327-79-70

«...назад