Подшипник INA MKUVE15-KGT05 INA / FAG

Print

Linear actuators
V guideways with angled cylindrical roller flat cage- corrosion-resistant design possible
Описание:
"
H85 -mm -
 - -
B63 -mm -
 - -
L160 -mm -
 - -
 -
1) -
 -Funnel type lubrication nipple to DIN 3405-AM6
2) -
 -Length calculation:
L2 = total stroke x 1,19 + L + 25
L tot = total stroke x 1,19 + L + 75
Total stroke (GH) = effective stroke + 2 x S (mm)

ATTENTION: The allowance S designates a safety range suitable for the particular application и should at least be equivalent to the spindle pitch Pz- total stroke in mm.

Maximum support rail length L2 = 5300 mm. Actuators with a total stroke length over 700 mm can be fitted with movable spindle supports (suffix SPU or 2SPU).
B130 -mm -
 - -
B240 -mm -
 - -
B365 -mm -
 - -
B451 -mm -
 - -
d10 -mm -
 -Tolerance for diameter: h6
d160 -mm -
 -Tolerance for diameter: g6
H152,5 -mm -
 - -
H284 -mm -
 - -
H322 -mm -
 - -
H444 -mm -
 - -
H568 -mm -
 - -
H651 -mm -
 - -
H79 -mm -
 - -
L315 -mm -
 - -
L438 -mm -
 - -
L512,2 -mm -
 - -
L613 -mm -
 - -
L725 -mm -
 - -
L825 -mm -
 - -
O1M6 -
 - -
 -
C0a24,7 -kN -
 -Spindle bearing arrangement:
Values are valid only for calculating Lh.
Basic axial load rating = for design criteria for the locating bearing, see Catalogue HR1, Rolling Bearings
Ca16,9 -kN -
 -Spindle bearing arrangement:
Values are valid only for calculating Lh.
Basic axial load rating = for design criteria for the locating bearing, see Catalogue HR1, Rolling Bearings
do x Pz16 x 5 -
 -Threaded spindle:
do x Pz = nominal spindle diameter x spindle pitch
M0z700 -Nm -
 -Permissible static moment of carriage guidance system:
The values are single loads и apply when the underside of the actuator is fully supported.
These must be reduced for combined loads.
For design criteria of the linear guidance system, see Catalogue PF1, Monorail Guidance Systems.
M0y700 -Nm -
 -Permissible static moment of carriage guidance system:
The values are single loads и apply when the underside of the actuator is fully supported.
These must be reduced for combined loads.
For design criteria of the linear guidance system, see Catalogue PF1, Monorail Guidance Systems.
M0x300 -Nm -
 -Permissible static moment of carriage guidance system:
The values are single loads и apply when the underside of the actuator is fully supported.
These must be reduced for combined loads.
For design criteria of the linear guidance system, see Catalogue PF1, Monorail Guidance Systems.
lz77 -cm^4 -
 -Geometrical moments of inertia of support rail
ly96 -cm^4 -
 -Geometrical moments of inertia of support rail
mLaw1,4 -kg -
 -Вес of carriage
mtot(Ltot - 50) x 0,08 + 2,4 -kg -
 - -
CI9,3 -kN -
 -Basic load ratings of spindle nut
Values are valid only for calculating Lh.
F = single nut
FM = preloaded double nut

Basic load ratings C и C0 to DIN 69051. Due to the incorporated calculation algorithm, the C и C0 values may differ in comparison with earlier results to DIN 69051.
C0 I13,1 -kN -
 -Basic load ratings of spindle nut
Values are valid only for calculating Lh.
F = single nut
FM = preloaded double nut

Basic load ratings C и C0 to DIN 69051. Due to the incorporated calculation algorithm, the C и C0 values may differ in comparison with earlier results to DIN 69051.
C029 -kN -
 -Basic load ratings of track roller guidance system
Values are valid only for calculating Lh.
C11,7 -kN -
 -Basic load ratings of track roller guidance system
Values are valid only for calculating Lh.
 -F/FM -
 -Spindle nut:
F = single nut
FM = preloaded double nut
"

Подшипник INA / FAG MKUVE15-KGT05

INA / FAG MKUVE15-KGT05
Наличие: Уточняйте

Поставщик:

(812) 327-79-70

«...назад